# WEEWX CONFIGURATION FILE # # Copyright (c) 2009-2024 Tom Keffer # See the file LICENSE.txt for your rights. ############################################################################## # This section is for general configuration information. # Set to 1 for extra debug info, otherwise comment it out or set to zero. debug = 0 # Whether to log successful operations. May get overridden below. log_success = True # Whether to log unsuccessful operations. May get overridden below. log_failure = True # This configuration file was created by ... version = 5.0.2 # Whether to try indefinitely to load the driver loop_on_init = 1 ############################################################################## # This section is for information about the station. [Station] # Description of the station location, such as your town. location = Wetterstation Kreuzau # Latitude in decimal degrees. Negative for southern hemisphere. latitude = 51.272 # Longitude in decimal degrees. Negative for western hemisphere. longitude = 6.553 # Altitude of the station, with the unit it is in. This is used only # if the hardware cannot supply a value. altitude = 216, meter # Choose 'foot' or 'meter' for unit # Set to type of station hardware. There must be a corresponding stanza # in this file, which includes a value for the 'driver' option. station_type = Interceptor # If you have a website, you may specify an URL station_url = 192.168.1.31 # The start of the rain year (1=January; 10=October, etc.). This is # downloaded from the station if the hardware supports it. rain_year_start = 1 # Start of week (0=Monday, 6=Sunday) week_start = 0 ############################################################################## [Interceptor] driver = user.interceptor device_type = ecowitt-client port = 8080 # Port den man bei Customserver eingetragen hat oder auch in FOSHKplugin iface = eth0 #mit Lan verbunden #iface = wlan0 # wenn mit WLAn verbunden ###[[sensor_map_extensions]] ###rainBatteryStatus = wh40_batt ###windBatteryStatus = ws80_batt ###hailBatteryStatus = ws90_batt #ws80_batt = ws80_batt ###ws90_batt = ws90_batt #outTempBatteryStatus = wh24_batt # outTempBatteryStatus = wh26_batt # outTempBatteryStatus = wh65_batt # outTempBatteryStatus = wh68_batt ###inTempBatteryStatus = wh25_batt [GW1000] # This section is for the Ecowitt Gateway driver. # How often to poll the API, default is every 20 seconds: poll_interval = 30 # The driver to use: driver = user.gw1000 ip_address = 192.168.1.31 port = 45000 #################################################### #wh32 = True #ignore_legacy_wh40_battery = True #show_all_batt = False log_unknown_fields = True #debug_rain = False #debug_wind = False #debug_loop = False #debug_sensors = False [[field_map_extensions]] batteryStatus1 = wh31_ch1_batt batteryStatus2 = wh31_ch2_batt batteryStatus3 = wh31_ch3_batt batteryStatus4 = wh31_ch4_batt batteryStatus5 = wh31_ch5_batt batteryStatus6 = wh31_ch6_batt batteryStatus7 = wh31_ch7_batt batteryStatus8 = wh31_ch8_batt lightning_distance = lightningdist lightning_disturber_count = lightningdettime lightning_Batt = wh57_batt co2_Temp = temp17 co2_Hum = humid17 pm10_0 = pm10 pm2_5 = pm255 co2_Batt = wh45_batt pm25_1 = pm251 pm25_2 = pm252 pm25_3 = pm253 pm25_4 = pm254 pm25_Batt1 = wh41_ch1_batt pm25_Batt2 = wh41_ch2_batt pm25_Batt3 = wh41_ch3_batt pm25_Batt4 = wh41_ch4_batt soilTemp1 = temp9 soilTemp2 = temp10 soilTemp3 = temp11 soilTemp4 = temp12 soilTemp5 = temp13 soilTemp6 = temp14 soilTemp7 = temp15 soilTemp8 = temp16 soilTempBatt1 = wn34_ch1_batt soilTempBatt2 = wn34_ch2_batt soilTempBatt3 = wn34_ch3_batt soilTempBatt4 = wn34_ch4_batt soilTempBatt5 = wn34_ch5_batt soilTempBatt6 = wn34_ch6_batt soilTempBatt7 = wn34_ch7_batt soilTempBatt8 = wn34_ch8_batt soilMoistBatt1 = wh51_ch1_batt soilMoistBatt2 = wh51_ch2_batt soilMoistBatt3 = wh51_ch3_batt soilMoistBatt4 = wh51_ch4_batt soilMoistBatt5 = wh51_ch5_batt soilMoistBatt6 = wh51_ch6_batt soilMoistBatt7 = wh51_ch7_batt soilMoistBatt8 = wh51_ch8_batt leak_1 = leak1 leak_2 = leak2 leak_3 = leak3 leak_4 = leak4 leak_Batt1 = wh55_ch1_batt leak_Batt2 = wh55_ch2_batt leak_Batt3 = wh55_ch3_batt leak_Batt4 = wh55_ch4_batt leafWetBatt1 = wn35_ch1_batt leafWetBatt2 = wn35_ch2_batt leafWetBatt3 = wn35_ch3_batt leafWetBatt4 = wn35_ch4_batt leafWetBatt5 = wn35_ch5_batt leafWetBatt6 = wn35_ch6_batt leafWetBatt7 = wn35_ch7_batt leafWetBatt8 = wn35_ch8_batt rainBatteryStatus = wh40_batt windBatteryStatus = ws80_batt hailBatteryStatus = ws90_batt #ws80_batt = ws80_batt #ws90_batt = ws90_batt outTempBatteryStatus = wh24_batt # outTempBatteryStatus = wh26_batt # outTempBatteryStatus = wh65_batt # outTempBatteryStatus = wh68_batt inTempBatteryStatus = wh25_batt consBatteryVoltage = ws1900batt maxdailygust = daymaxwind pm25_24h_co2 = pm255_24h_avg pm10_24h_co2 = pm10_24h_avg pm25_avg_24h_ch1 = pm251_24h_avg pm25_avg_24h_ch2 = pm252_24h_avg pm25_avg_24h_ch3 = pm253_24h_avg pm25_avg_24h_ch4 = pm254_24h_avg lightningcount = lightningcount co2_24h = co2_24h_avg barometer = relbarometer rainrate = rainrate #ok totalRain = raintotal eventRain = rainevent #ok hourRain = t_rainhour dayRain = t_rainday weekRain = t_rainweek monthRain = t_rainmonth yearRain = t_rainyear rain_piezo = p_rain erain_piezo = p_rainevent rrain_piezo = p_rainrate hrain_piezo = p_hourrain drain_piezo = p_rainday wrain_piezo = p_rainweek mrain_piezo = p_rainmonth yrain_piezo = p_rainyear hail = p_rain hailRate = p_rainrate wh24_sig = wh24_sig wh25_sig = wh25_sig wh31_ch1_sig = wh31_ch1_sig ws80_sig = ws80_sig ws90_sig = ws90_sig wh40_sig = wh40_sig wh45_sig = wh45_sig wh57_sig = wh57_sig wh51_ch1_sig = wh51_ch1_sig wn35_ch1_sig = wn35_ch1_sig wn34_ch1_sig = wn34_ch1_sig rain_source = rain_source rain_day_reset = rain_day_reset rain_week_reset = rain_week_reset rain_annual_reset = rain_annual_reset raingain = raingain gain0 = gain0 gain1 = gain1 gain2 = gain2 gain3 = gain3 gain4 = gain4 gain5 = gain5 gain6 = gain6 gain7 = gain7 gain8 = gain8 gain9 = gain9 heap = heap ####################### ############################################################################## [Simulator] # This section is for the weewx weather station simulator. # The time (in seconds) between LOOP packets. loop_interval = 2.5 # The simulator mode can be either 'simulator' or 'generator'. # Real-time simulator. Sleep between each LOOP packet. mode = simulator # Generator. Emit LOOP packets as fast as possible (useful for testing). #mode = generator # The start time. Format is YYYY-mm-ddTHH:MM. If not specified, the # default is to use the present time. #start = 2011-01-01T00:00 # The driver to use. driver = weewx.drivers.simulator ############################################################################## # This section is for uploading data to Internet sites [StdRESTful] # Uncomment and change to override logging for uploading services. log_success = True log_failure = True [[StationRegistry]] # To register this weather station at weewx.com, set this to true, and # set option 'station_url', located in the [Station] section above. register_this_station = False [[AWEKAS]] # This section is for configuring posts to AWEKAS. # If you wish to post to AWEKAS, set the option 'enable' to true, then # specify a username and password. # Use quotes around the password to guard against parsing errors. enable = false username = replace_me password = replace_me [[CWOP]] # This section is for configuring posts to CWOP. # If you wish to post to CWOP, set the option 'enable' to true, # then specify the station ID (e.g., CW1234). enable = false station = replace_me # If this is an APRS (radio amateur) station, specify the # passcode (e.g., 12345). Otherwise, ignore. passcode = replace_me [[PWSweather]] # This section is for configuring posts to PWSweather.com. # If you wish to post to PWSweather.com, set the option 'enable' to # true, then specify a station and password. # Use quotes around the password to guard against parsing errors. enable = false station = replace_me password = replace_me [[WOW]] # This section is for configuring posts to WOW. # If you wish to post to WOW, set the option 'enable' to true, then # specify a station and password. # Use quotes around the password to guard against parsing errors. enable = false station = replace_me password = replace_me [[Wunderground]] # This section is for configuring posts to the Weather Underground. # If you wish to post to the Weather Underground, set the option # 'enable' to true, then specify a station (e.g., 'KORHOODR3'). Use # the station key (find it at # https://www.wunderground.com/member/devices) for the password. enable = false station = replace_me password = replace_me # Set the following to True to have weewx use the WU "Rapidfire" # protocol. Not all hardware can support it. See the User's Guide. rapidfire = False ############################################################################## # This section specifies what reports, using which skins, to generate. [StdReport] # Where the skins reside, relative to WEEWX_ROOT SKIN_ROOT = skins # Where the generated reports should go, relative to WEEWX_ROOT HTML_ROOT = /var/www/html/weewx lang = de # Uncomment and change to override logging for reports. log_success = True log_failure = True # The database binding indicates which data should be used in reports. data_binding = wx_binding # Each of the following subsections defines a report that will be run. # See the customizing guide to change the units, plot types and line # colors, modify the fonts, display additional sensor data, and other # customizations. Many of those changes can be made here by overriding # parameters, or by modifying templates within the skin itself. [[SeasonsReport]] # The SeasonsReport uses the 'Seasons' skin, which contains the # images, templates and plots for the report. skin = Seasons enable = true HTML_ROOT = /var/www/html/weewx/standard [[SmartphoneReport]] # The SmartphoneReport uses the 'Smartphone' skin, and the images and # files are placed in a dedicated subdirectory. skin = Smartphone enable = False HTML_ROOT = /var/www/html/weewx/smartphone [[MobileReport]] # The MobileReport uses the 'Mobile' skin, and the images and files # are placed in a dedicated subdirectory. skin = Mobile enable = false HTML_ROOT = /var/www/html/weewx/mobile [[StandardReport]] # This is the old "Standard" skin. By default, it is not enabled. skin = Standard enable = false HTML_ROOT = /var/www/html/weewx/standard [[WdcReport]] skin = weewx-wdc enable = false HTML_ROOT = /var/www/html/weewx/wdc [[Belchertown]] skin = Belchertown HTML_ROOT = /var/www/html/weewx/belchertown enable = false [[[Extras]]] # For help refer to the docs at https://github.com/poblabs/weewx-belchertown # and consult skin.conf for the configurable elements and their hierarchy #--- General Options --- # belchertown_debug = 0 # belchertown_locale = "auto" # theme = light # theme_toggle_enabled = 1 # logo_image = "" # logo_image_dark = "" # site_title = "My Weather Website" # station_observations = "barometer","dewpoint","outHumidity","rainWithRainRate" # beaufort_category = 0 # manifest_name = "My Weather Website" # manifest_short_name = "MWW" # aeris_map = 0 # radar_html = '' # (default seems to center on your lat/lon) # radar_html_dark = None # radar_zoom = 8 # radar_marker = 0 # almanac_extras = 1 # highcharts_enabled = 1 # graph_page_show_all_button = 1 # graph_page_default_graphgroup = "day" # highcharts_homepage_graphgroup = "day" # highcharts_decimal = "auto" # highcharts_thousands = "auto" # googleAnalyticsId = "" # pi_kiosk_bold = "false" # pi_theme = "auto" # webpage_autorefresh = 0 # reload_hook_images = 0 # reload_images_radar = 300 # reload_images_hook_asi = -1 # reload_images_hook_af = -1 # reload_images_hook_as = -1 # reload_images_hook_ac = -1 # show_last_updated_alert = 0 # last_updated_alert_threshold = 1800 #--- MQTT Websockets (for Real Time Streaming) Options --- # mqtt_websockets_enabled = 0 # mqtt_websockets_host = "" # mqtt_websockets_port = 8080 # mqtt_websockets_ssl = 0 # mqtt_websockets_topic = "" # disconnect_live_website_visitor = 1800000 #--- Forecast Options --- # forecast_enabled = 0 # forecast_provider = "aeris" # forecast_api_id = "" # forecast_api_secret = "" # forecast_units = "us" # forecast_lang = "en" # forecast_stale = 3540 # forecast_aeris_use_metar = 1 # forecast_interval_hours = 24 # forecast_alert_enabled = 0 # forecast_alert_limit = 1 # forecast_show_daily_forecast_link = 0 # forecast_daily_forecast_link = "" # aqi_enabled = 0 # aqi_location_enabled = 0 #--- Earthquake Options --- # earthquake_enabled = 0 # earthquake_maxradiuskm = 1000 # earthquake_stale = 10740 # earthquake_server = USGS # geonet_mmi = 4 #--- Social Options --- # facebook_enabled = 0 # twitter_enabled = 0 # twitter_hashtags = "weewx #weather" # social_share_html = "" #--- Kiosk Options --- # radar_html_kiosk = "" # radar_width_kiosk = 490 # radar_height_kiosk = 362 # mqtt_websockets_host_kiosk = "" # mqtt_websockets_port_kiosk = "" # mqtt_websockets_ssl_kiosk = "" # forecast_interval_hours_kiosk = 24 # aqi_enabled_kiosk = 0 #------------------------------------------------------------- #--- #--- python's ConfigObj has a limitation in how it processes #--- comments, so we need to define an 'unused' variable below #--- to ensure that this whole stanza makes it into weewx.conf #--- #--- please ignore the following 'unused' variable #--- #------------------------------------------------------------- work_around_ConfigObj_limitations = true [[FTP]] # FTP'ing the results to a webserver is treated as just another report, # albeit one with an unusual report generator! skin = Ftp # If you wish to use FTP, set "enable" to "true", then fill out the # next four lines. # Use quotes around the password to guard against parsing errors. enable = true user = password = server = # The ftp server name, e.g, www.myserver.org path = / # The destination directory, e.g., /weather # Set to True for an FTP over TLS (FTPS) connection. Not all servers # support this. secure_ftp = False # To upload files from something other than what HTML_ROOT is set # to above, specify a different HTML_ROOT here. HTML_ROOT = /var/www/html/weewx # Most FTP servers use port 21. port = 21 # Set to 1 to use passive mode, zero for active mode passive = 1 [[RSYNC]] # rsync'ing to a webserver is treated as just another report. skin = Rsync # If you wish to use rsync, you must configure passwordless ssh using # public/private key authentication from the user account that weewx # runs to the user account on the remote machine where the files # will be copied. # # If you wish to use rsync, set "enable" to "true", then # fill out server, user, and path. # The server should appear in your .ssh/config file. # The user is the username used in the identity file. # The path is the destination directory, such as /var/www/html/weather. # Be sure that the user has write permissions on the destination! enable = false server = replace_me user = replace_me path = replace_me # To upload files from something other than what HTML_ROOT is set # to above, specify a different HTML_ROOT here. #HTML_ROOT = /var/www/html/weewx # Rsync can be configured to remove files from the remote server if # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you # make a mistake in the remote path, you could could unintentionally # cause unrelated files to be deleted. Set to 1 to enable remote file # deletion, zero to allow files to accumulate remotely. delete = 0 # Options in the [[Defaults]] section below will apply to all reports. # What follows are a few of the more popular options you may want to # uncomment, then change. [[Defaults]] # Which language to use for all reports. Not all skins support all # languages. You can override this for individual reports. lang = de # Which unit system to use for all reports. Choices are 'us', 'metric', # or 'metricwx'. You can override this for individual reports. unit_system = metric [[[Units]]] # Option "unit_system" above sets the general unit system, but # overriding specific unit groups is possible. These are popular # choices. Uncomment and set as appropriate. The unit is always # in the singular, e.g., 'mile_per_hour', NOT 'miles_per_hour' [[[[Groups]]]] group_altitude = meter # Options are 'foot' or 'meter' group_pressure = hPa # Options are 'inHg', 'mmHg', 'mbar', or 'hPa' group_rain = mm # Options are 'inch', 'cm', or 'mm' group_rainrate = mm_per_hour # Options are 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour' group_temperature = degree_C # Options are 'degree_C', 'degree_F', or 'degree_K' group_deltatime = hour # The following line is used to keep the above lines indented # properly. It can be ignored. unused = unused # Uncommenting the following section frequently results in more # attractive formatting of times and dates, but may not work in # your locale. [[[[TimeFormats]]]] # day = %H:%M # week = %H:%M on %A # month = %d-%b-%Y %H:%M # year = %d-%b-%Y %H:%M # rainyear = %d-%b-%Y %H:%M # current = %d-%b-%Y %H:%M # ephem_day = %H:%M # ephem_year = %d-%b-%Y %H:%M # The following line is used to keep the above lines indented # properly. It can be ignored. unused = unused [[[Labels]]] # Users frequently change the labels for these observation types. [[[[Generic]]]] # inHumidity = Inside Humidity # inTemp = Inside Temperature # outHumidity = Outside Humidity # outTemp = Outside Temperature # extraTemp1 = Temperature1 # extraTemp2 = Temperature2 # extraTemp3 = Temperature3 # The following line is used to keep the above lines indented # properly. It can be ignored. unused = unused ############################################################################## # This service converts the unit system coming from the hardware to a unit # system in the database. [StdConvert] # The target_unit affects only the unit system in the database. Once # chosen it cannot be changed without converting the entire database. # Modification of target_unit after starting weewx will result in # corrupt data - the database will contain a mix of US and METRIC data. # # The value of target_unit does not affect the unit system for # reporting - reports can display US, Metric, or any combination of units. # # In most cases, target_unit should be left as the default: US # # In particular, those migrating from a standard wview installation # should use US since that is what the wview database contains. # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING! target_unit = US # Options are 'US', 'METRICWX', or 'METRIC' ############################################################################## # This section can adjust data using calibration expressions. [StdCalibrate] [[Corrections]] # For each type, an arbitrary calibration expression can be given. # It should be in the units defined in the StdConvert section. # Example: foo = foo + 0.2 radiation = luminosity / 126.7 if luminosity is not None else None #rxCheckPercent = ws80_sig * 25 if ws80_sig is not None else None rxCheckPercent = ws90_sig * 25 if ws90_sig is not None else None hail = p_rain if p_rain is not None else None hailRate = p_rainrate if p_rainrate is not None else None signal1 = wh31_ch1_sig * 25 if wh31_ch1_sig is not None else None signal2 = wh31_ch2_sig * 25 if wh31_ch2_sig is not None else None signal3 = wh31_ch3_sig * 25 if wh31_ch3_sig is not None else None signal4 = wh31_ch4_sig * 25 if wh31_ch4_sig is not None else None signal5 = wh31_ch5_sig * 25 if wh31_ch5_sig is not None else None signal6 = wh31_ch6_sig * 25 if wh31_ch6_sig is not None else None signal7 = wh31_ch7_sig * 25 if wh31_ch7_sig is not None else None signal8 = wh31_ch8_sig * 25 if wh31_ch8_sig is not None else None wh40_sig = wh40_sig * 25 if wh40_sig is not None else None ws90_sig = ws90_sig * 25 if ws90_sig is not None else None wh57_sig = wh57_sig * 25 if wh57_sig is not None else None wh45_sig = wh45_sig * 25 if wh45_sig is not None else None wn34_ch1_sig = wn34_ch1_sig * 25 if wn34_ch1_sig is not None else None pb = heap if heap is not None else None ############################################################################## # This section is for quality control checks. If units are not specified, # values must be in the units defined in the StdConvert section. [StdQC] [[MinMax]] barometer = 26, 32.5, inHg pressure = 24, 34.5, inHg outTemp = -40, 120, degree_F inTemp = 10, 120, degree_F outHumidity = 0, 100 inHumidity = 0, 100 windSpeed = 0, 120, mile_per_hour rain = 0, 10, inch ############################################################################## # This section controls the origin of derived values. [StdWXCalculate] [[Calculations]] # How to calculate derived quantities. Possible values are: # hardware - use the value provided by hardware # software - use the value calculated by weewx # prefer_hardware - use value provide by hardware if available, # otherwise use value calculated by weewx pressure = prefer_hardware altimeter = prefer_hardware appTemp = prefer_hardware barometer = prefer_hardware cloudbase = prefer_hardware dewpoint = prefer_hardware ET = prefer_hardware heatindex = prefer_hardware humidex = prefer_hardware inDewpoint = prefer_hardware maxSolarRad = prefer_hardware rainRate = prefer_hardware windchill = prefer_hardware windrun = prefer_hardware GTS = software, archive GTSdate = software, archive utcoffsetLMT = software, archive dayET = prefer_hardware, archive ET24 = prefer_hardware, archive yearGDD = software, archive seasonGDD = software, archive outVaporP = software, loop outSVP = software, loop outMixingRatio = software, loop outEquiTemp = software, loop outThetaE = software, loop outHumAbs = software, loop boilingTemp = software, loop ############################################################################## # For hardware that supports it, this section controls how often the # onboard clock gets updated. [StdTimeSynch] # How often to check the weather station clock for drift (in seconds) clock_check = 14400 # How much it can drift before we will correct it (in seconds) max_drift = 5 ############################################################################## # This section is for configuring the archive service. [StdArchive] # If the station hardware supports data logging then the archive interval # will be downloaded from the station. Otherwise, specify it (in seconds). archive_interval = 300 # If possible, new archive records are downloaded from the station # hardware. If the hardware does not support this, then new archive # records will be generated in software. # Set the following to "software" to force software record generation. record_generation = software # Whether to include LOOP data in hi/low statistics. loop_hilo = True # Uncomment and change to override logging for archive operations. log_success = True log_failure = True # The data binding used to save archive records. data_binding = wx_binding ############################################################################## # This section binds a data store to a database. [DataBindings] [[wx_binding]] # The database must match one of the sections in [Databases]. # This is likely to be the only option you would want to change. database = archive_sqlite # The name of the table within the database. table_name = archive # The manager handles aggregation of data for historical summaries. manager = weewx.manager.DaySummaryManager # The schema defines the structure of the database. # It is *only* used when the database is created. schema = schemas.wview_extended.schema ############################################################################## # This section defines various databases. [Databases] # A SQLite database is simply a single file. [[archive_sqlite]] database_name = weewx.sdb database_type = SQLite # MySQL [[archive_mysql]] database_name = weewx database_type = MySQL ############################################################################## # This section defines defaults for the different types of databases. [DatabaseTypes] # Defaults for SQLite databases. [[SQLite]] driver = weedb.sqlite # Directory in which database files are located, relative to WEEWX_ROOT SQLITE_ROOT = /var/lib/weewx # Defaults for MySQL databases. [[MySQL]] driver = weedb.mysql # The host where the database is located. host = localhost # The user name for logging in to the host. user = weewx # Use quotes around the password to guard against parsing errors. password = weewx ############################################################################## # This section configures the internal weewx engine. [Engine] # This section specifies which services should be run and in what order. [[Services]] prep_services = weewx.engine.StdTimeSynch data_services = user.gw1000.Gw1000Service process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate, user.sunrainduration.SunshineDuration xtype_services = weewx.wxxtypes.StdWXXTypes, weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater, weewx.wxxtypes.StdDelta, user.GTS.GTSService archive_services = weewx.engine.StdArchive restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS report_services = weewx.engine.StdPrint, weewx.engine.StdReport [Accumulator] # Start Ecowitt Gateway driver extractors [[daymaxwind]] extractor = last [[lightning_distance]] extractor = last [[lightning_strike_count]] extractor = sum [[lightningcount]] extractor = last [[lightning_last_det_time]] extractor = last [[stormRain]] extractor = last [[hourRain]] extractor = last [[dayRain]] extractor = last [[weekRain]] extractor = last [[monthRain]] extractor = last [[yearRain]] extractor = last [[totalRain]] extractor = last [[p_rain]] extractor = sum [[p_stormRain]] extractor = last [[p_dayRain]] extractor = last [[p_weekRain]] extractor = last [[p_monthRain]] extractor = last [[p_yearRain]] extractor = last [[t_rain]] extractor = sum [[t_stormRain]] extractor = last [[t_dayRain]] extractor = last [[t_weekRain]] extractor = last [[_monthRain]] extractor = last [[t_yearRain]] extractor = last [[pm2_51_24h_avg]] extractor = last [[pm2_52_24h_avg]] extractor = last [[pm2_53_24h_avg]] extractor = last [[pm2_54_24h_avg]] extractor = last [[pm2_55_24h_avg]] extractor = last [[pm10_24h_avg]] extractor = last [[co2_24h_avg]] extractor = last [[heap_free]] extractor = last [[wh40_batt]] extractor = last [[wh26_batt]] extractor = last [[wh25_batt]] extractor = last [[wh24_batt]] extractor = last [[wh65_batt]] extractor = last [[wh31_ch1_batt]] extractor = last [[wh31_ch2_batt]] extractor = last [[wh31_ch3_batt]] extractor = last [[wh31_ch4_batt]] extractor = last [[wh31_ch5_batt]] extractor = last [[wh31_ch6_batt]] extractor = last [[wh31_ch7_batt]] extractor = last [[wh31_ch8_batt]] extractor = last [[wn34_ch1_batt]] extractor = last [[wn34_ch2_batt]] extractor = last [[wn34_ch3_batt]] extractor = last [[wn34_ch4_batt]] extractor = last [[wn34_ch5_batt]] extractor = last [[wn34_ch6_batt]] extractor = last [[wn34_ch7_batt]] extractor = last [[wn34_ch8_batt]] extractor = last [[wn35_ch1_batt]] extractor = last [[wn35_ch2_batt]] extractor = last [[wn35_ch3_batt]] extractor = last [[wn35_ch4_batt]] extractor = last [[wn35_ch5_batt]] extractor = last [[wn35_ch6_batt]] extractor = last [[wn35_ch7_batt]] extractor = last [[wn35_ch8_batt]] extractor = last [[wh41_ch1_batt]] extractor = last [[wh41_ch2_batt]] extractor = last [[wh41_ch3_batt]] extractor = last [[wh41_ch4_batt]] extractor = last [[wh45_batt]] extractor = last [[wh51_ch1_batt]] extractor = last [[wh51_ch2_batt]] extractor = last [[wh51_ch3_batt]] extractor = last [[wh51_ch4_batt]] extractor = last [[wh51_ch5_batt]] extractor = last [[wh51_ch6_batt]] extractor = last [[wh51_ch7_batt]] extractor = last [[wh51_ch8_batt]] extractor = last [[wh51_ch9_batt]] extractor = last [[wh51_ch10_batt]] extractor = last [[wh51_ch11_batt]] extractor = last [[wh51_ch12_batt]] extractor = last [[wh51_ch13_batt]] extractor = last [[wh51_ch14_batt]] extractor = last [[wh51_ch15_batt]] extractor = last [[wh51_ch16_batt]] extractor = last [[wh55_ch1_batt]] extractor = last [[wh55_ch2_batt]] extractor = last [[wh55_ch3_batt]] extractor = last [[wh55_ch4_batt]] extractor = last [[wh57_batt]] extractor = last [[wh68_batt]] extractor = last [[ws80_batt]] extractor = last [[ws90_batt]] extractor = last [[wh40_sig]] extractor = last [[wh26_sig]] extractor = last [[wh25_sig]] extractor = last [[wh24_sig]] extractor = last [[wh65_sig]] extractor = last [[wh31_ch1_sig]] extractor = last [[wh31_ch2_sig]] extractor = last [[wh31_ch3_sig]] extractor = last [[wh31_ch4_sig]] extractor = last [[wh31_ch5_sig]] extractor = last [[wh31_ch6_sig]] extractor = last [[wh31_ch7_sig]] extractor = last [[wh31_ch8_sig]] extractor = last [[wn34_ch1_sig]] extractor = last [[wn34_ch2_sig]] extractor = last [[wn34_ch3_sig]] extractor = last [[wn34_ch4_sig]] extractor = last [[wn34_ch5_sig]] extractor = last [[wn34_ch6_sig]] extractor = last [[wn34_ch7_sig]] extractor = last [[wn34_ch8_sig]] extractor = last [[wn35_ch1_sig]] extractor = last [[wn35_ch2_sig]] extractor = last [[wn35_ch3_sig]] extractor = last [[wn35_ch4_sig]] extractor = last [[wn35_ch5_sig]] extractor = last [[wn35_ch6_sig]] extractor = last [[wn35_ch7_sig]] extractor = last [[wn35_ch8_sig]] extractor = last [[wh41_ch1_sig]] extractor = last [[wh41_ch2_sig]] extractor = last [[wh41_ch3_sig]] extractor = last [[wh41_ch4_sig]] extractor = last [[wh45_sig]] extractor = last [[wh51_ch1_sig]] extractor = last [[wh51_ch2_sig]] extractor = last [[wh51_ch3_sig]] extractor = last [[wh51_ch4_sig]] extractor = last [[wh51_ch5_sig]] extractor = last [[wh51_ch6_sig]] extractor = last [[wh51_ch7_sig]] extractor = last [[wh51_ch8_sig]] extractor = last [[wh51_ch9_sig]] extractor = last [[wh51_ch10_sig]] extractor = last [[wh51_ch11_sig]] extractor = last [[wh51_ch12_sig]] extractor = last [[wh51_ch13_sig]] extractor = last [[wh51_ch14_sig]] extractor = last [[wh51_ch15_sig]] extractor = last [[wh51_ch16_sig]] extractor = last [[wh55_ch1_sig]] extractor = last [[wh55_ch2_sig]] extractor = last [[wh55_ch3_sig]] extractor = last [[wh55_ch4_sig]] extractor = last [[wh57_sig]] extractor = last [[wh68_sig]] extractor = last [[ws80_sig]] extractor = last [[ws90_sig]] extractor = last [RadiationDays] min_sunshine = 120 # Entry of extension radiationhours.py, if is installed (= limit value) sunshine_coeff = 0.8 # Factor from which value sunshine is counted - the higher the later sunshine_min = 18 # below this value (W/m²), sunshine is not taken into account. sunshine_loop = 1 # use for sunshine loop packet (or archive: sunshine_loop = 0) rainDur_loop = 0 # use for rain duration loop packet - default is not hailDur_loop = 0 # use for piezo-rain duration loop packet - default is not sunshine_log = 1 # should not be logged when sunshine is recorded rainDur_log = 1 # no logging for rain duration hailDur_log = 1 # no logging for piezo-rain duration rain2 = 0 # no rain2 available (Davis Live, Davis Console) sunshine2 = 0 # no shunhine2 available (Davis Live, Davis Console) sunshine2_loop = 1 rainDur2_loop = 0 sunshine2_log = 0 rainDur2_log = 0